Tile adhesive glue packed in 20kg or 25kg per bag, customizes packaging is available
Tile adhesive glue will be ready in 5 days
Shunan Ceramic tile fixing adhesive is a professional-grade, polymer modified high quality Chinese Conch cement based adhesive material. This thin-set mortar is Ideal for placing and laying all types of ceramic floor tiles and some ceramic wall tiles in dry and wet areas.
20kg or 25kg per bag, customizes packaging is available
Scope of Use
Can be used for fixing floor tiles on concrete floor, cement plaster, concrete panel, brickwork with plaster and most of waterproof coating surface directly.
2. Ideal for installing internal wall tile which water absorption rate is ≥ 0.5%,and size is ≤ 300 x 600mm
Cementitious grey powder
Mix Ratio With Water
20kg / 5 liter
~ 2 hours
~ 20 minutes
Resistance to damp
Adhesion according to JC/T547-2005
(initial adhesion - 28 days)
≥ 0.5 MPa
Up to 30 minutes
3 - 5 mm when the tile is adhered
Approx. 4 - 5m2 / 20kg bag
1. Substrate must be even, sound, clean, free of dust, grease, waxiness or release agent which may influence bonding.
2. Initial finish coat surface should be done coarse treatment, area of coating residues should not exceed 20% of original surface.
3. Fresh concrete substrate can be tiled at age of 28 days, Fresh plaster substrate can be tiled at the age of 7days.
4. Old concrete and plaster substrate should be tiled after being cleaned by industrial detergent or degreaser and washed by high pressure tap and dried in the air for 24 hours.
5. Substrate should be coating with Interface agent if Impregnate concrete with high coefficient of water absorption or dust is hard to remove.
6. Substrate should be wet inside and dry outside before construction in such conditions: high temperature, dry conditions or high water absorption.
Pour clean water into a mixing container by water/powder proportion of 1:4, before adding Shunan Ceramic Tile Adhesive slowly. Meantime, open agitator and start mixing evenly from top to bottom until completely free of paste. Allow the mixture to nature for a short time. Then mix again slightly before using.
Use a straight edge trowel to spread a layer of Shunan Ceramic Tile Adhesive on the construction substrate, afterwards comb the adhesive into full stripes in straight direction at the angle of 60º with substrate by using a suitable tooth form trowel, fix ceramic tiles on it last.
It should be double-sided gluing if the fissures on the back of ceramic tile is too deep or stone/ceramic tile) is too big and heavy. Namely, both substrate and back of tiles should be applied with adhesive at the same time.
Theoretical coverage is approx. 3.5 - 5 kg/m2 under the condition of even substrate. The specific consumption varies depending on different substrate and wall tiles.
Approx. 12 months if stored in a tightly sealed container, in cool and dry conditions. Use products in opened containers as soon as possible.
Best construction temperature: 5-35 ℃
Mixing ratio of water/powder could be adjusted appropriately according to the differences of the material and quality of the substrate, weather and construction conditions etc.
Well mixed adhesive should be used out within 2-3 hours , It should be abandoned instead of being recycled using after mixing with water when the mixing appearing induration .
Protection measures should be done during rainy days for exterior construction. Make sure the construction area can not get wet by rain and washing within 24 hours after construction.
The fixed tiles can accept foot traffic and can be grouted after the adhesive dried and solidified completely (approx. 24 hours).
Temporary fixation measures should be taken when fixing wall tiles.
ShunAn granite & marble adhesive is a professional-grade, high performance, one-component, polymer-modified thin-set mortar.
Unique, high polymer modification provides the superior bonding characteristics for installation of tile and stone over most surfaces.
Installation of ceramic and porcelain tile, quarry tile, pavers, most monocotturra tiles, slate, and most types of marble, granite and natural stone.
ShunAn granite & marble adhesive can be used to lay tiles onto the concrete, cement render, blockwork, rendered brickwork surfaces, cement board and calcium silicone board.
Excellent bond strength
Easy to use - just mix with water and apply
Water resistant when cured
All surfaces must be structurally sound, clean and free from movement, oil, grease, wax, curing compounds and other loose contaminating materials.
Painted surfaces must be scabbied to expose at least 80% of the original substrate.
New concrete must be allowed to cure for 28 days.
Newly rendered surfaces must be allowed to cure for at least 7 days.
Steel trowel finished surfaces must be acid etched or wire brushed prior to tiling.
For old concrete and rendered surfaces, a strong commercial grade detergent or degreaser must be used to clean.
All surface to be dry for at least 24 hours prior to tiling.
Ensure all release agents are removed from concrete surfaces, especially tilt-up slabs.
Cementitious grey powder
Water Powder Ratio
0.22 - 0.25 : 1
~ 2 hours
~ 20 minutes
≥ 1.5 Mpa
Up to 30 minutes
2 - 4 mm when the tile is adhered
4m2 / 20kg bag
Always add ShunAn granite & marble adhesive powder to clean water, mixing continuously until a thick creamy consistency is achieved.
The mixing ratio is 20kg of always add ShunAn granite & marble adhesive powder to approximately 4 - 4.8 litres of water.
Allow the mixture to stand for 10 minutes, remix then use the adhesive.
Spread the adhesive onto the substrate using a 6mmx6mm notched trowel for walls,a 10mmx10mm - 12mmx12mm notched trowel for floor tiles.
Ensure that there are no voids under the tiles. For tiles with deep grooves or ridges, the adhesive should be buttered onto the back of the tiles in the addition to being trowelled onto the substrate.
Note: the adhesive coverage must be uniform and cover the entire tile thoroughly. the bed thickness must be approximately half the height of the square notched trowel used.
Normal consumption of Shunan granite & marble adhesive is 3.5-7.0 kg/m2.
Consumption varies according to the site conditions and building up required.
1 year from production date when stored in dry, heated conditions.
PRODUCT STANDARD AND QUALITY DEGREE
The use of this product is beyond the manufacturer’s control, and liadility is rested to the replacement of materials proven faulty.The manufacturer is not responsible for any loss or damage arising from incorrect usage.
Manufacture under ISO9001 Quality Control and Management System